Do It Yourself Bathtub Installation.
Do It Yourself Bathtub Installation.
Blog Article
This article down below involving How to Install a Bathtub Yourself is especially remarkable. You should investigate it.
Setting up a tub isn't precisely rocket science, however it does need solid plumbing, carpentry, and sometimes, tiling skills. Changing an old bath tub with a brand-new one is likewise a reasonably tough job. If the old tub is readily available, the project can move speedily; if you have to open up a wall surface to eliminate the old tub and position the brand-new bath tub, the job is much harder. In either case, the project is within a residence handyman's abilities, although you will certainly need a helper to vacate the old bathtub as well as set in the new one. See to it you have actually certified yourself for the work and also are comfortable attempting it. As opposed to employing a specialist to take over a halfway-completed project, it is far better to think about employing one before you start. Possibilities are you may require an expert plumber to make tube connections.
This article will certainly assist you install a brand-new bathtub in your bathroom if you have actually already bought a brand-new tub and do not need to transform the plan of your previous supply of water pipelines.
Your devices and product checklist should consist of the following:
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you must do is disconnect the water system. After doing so, turn on the faucets to drain any kind of water staying in the system. The procedure of removing the existing faucets can be quite bothersome due to the limited access that is usually the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the faucets. Have a fabric all set for the staying water that will certainly come from the pipelines. Once the supply pipelines have actually been eliminated, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing compound.
Prior to moving on to fit the brand-new faucets, compare the pipe links on the old taps to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to avoid damages to the string. One end of the connector fits on the plastic tail of the faucet and also the other end offers a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly need lowering couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, position the tap in the installing opening in the bath/basin ensuring that the washers are in location in between the faucet and the sink. Secure the tap in position with the supplier provided backnut. Once the tap is safely in position, the supply pipelines can be attached to the tails of the taps. The taps can either be connected by using corrugated copper piping or with typical faucet adapters. The previous kind needs to be connected to the tap ends first, tightening only by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Mounting the Bathtub
Using the two wooden boards under its feet, place the bathtub in the required position. The wooden boards are useful in uniformly spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto 4 little points.
The next goal is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the spirit level and adjusting the feet on the bathtub until the spirit level reads degree.
To mount faucets, fit all-time low of the outermost versatile tap port to the suitable supply pipe by making a compression join; after that do the very same for the various other tap.
Turn on the supply of water and check all joints and brand-new pipework for leakages as well as tighten them if required. Fill up the bathtub as well as additionally examine the overflow electrical outlet as well as the regular electrical outlet for leaks.
Finally, fix the bathroom paneling as defined in the maker's instruction manual. Tiling and sealing around the bath tub must wait up until the bathtub has actually been made use of a minimum of once as this will certainly resolve it into its final placement.
Planning for the Setup
Firstly, the sustaining framework supplied with the bathroom must be fitted (if needed) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is necessary to make certain that if the tap comes with a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets unit to stop strain on the bath tub.
Fit the flexible tap connectors to the bottom of the two faucets utilizing 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you make use of all of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom should currently prepare to be fitted in its final setting.
Tiling Around the Bath tub
In the area where the bath satisfies the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate enough to break an inflexible seal, causing the water to permeate the wall surface between the bath and also the tiling, leading to issues with wetness and possible leakages to the ceiling below.
You can choose from a range of coloured sealers to blend in your fixtures as well as installations. They are sold in tubes as well as cartridges, and also are capable of securing voids up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of drenched paper or soft rope. Remember to always fill up the bath tub with water prior to sealing, to enable the motion experienced when the bathtub remains in use. The sealant can break rather very early if you do not take into account this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently readily available on the marketplace. It is advisable to fit the tiles utilizing water-resistant or water resistant sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a devoted reader on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I figured sharing that excerpt was a great idea. If you please take the time to share this article if you enjoyed reading it. Thanks so much for going through it.
Here Report this page